First, confirm it is a Wi-Fi problem
Before changing anything, check whether the problem is your Wi-Fi or your internet connection. Run a speed test standing next to the router, then again in the problem room.
- Slow next to the router as well: the issue is likely your internet service or the router itself. Contact your provider, and check that the plan speed matches what you are paying for.
- Fast next to the router, slow elsewhere: you have a Wi-Fi coverage problem, and the steps below will help.
Common causes of Wi-Fi dead spots
Router placement
Many routers sit where the NBN connection enters the home, which is often in a garage, cupboard or one corner of the house. Wi-Fi spreads outwards from the router, so a router at one end of the home leaves the far end weak.
Building materials
Brick, concrete, stone and especially metal weaken Wi-Fi significantly. Mirrors, foil-backed insulation, fridges and fish tanks also block signal. A double-brick home can need more access points than a home of the same size built with plasterboard.
The frequency band
Most routers broadcast on two bands. 2.4 GHz travels further and passes through walls better, but it is slower and more crowded. 5 GHz is much faster but has a shorter range. Newer 6 GHz Wi-Fi is faster again, with even shorter range. A device in a distant room may be stuck on a weak 5 GHz signal or a crowded 2.4 GHz one.
Interference
Neighbouring networks, microwave ovens, some cordless phones and baby monitors can interfere with the 2.4 GHz band. In apartments with many nearby networks, congestion can be a bigger problem than distance.
Fixes, from free to more involved
1. Move the router
Place the router as close to the centre of the home as practical, raised off the floor and out of cupboards. Even a few metres can make a noticeable difference. If the NBN connection box is in an awkward place, an Ethernet cable can connect it to a router in a better spot.
2. Update and restart
Install router firmware updates and restart the router. Older routers may not support newer Wi-Fi standards, and an outdated router can be the bottleneck for the whole home.
3. Adjust channels and bands
Most modern routers choose channels automatically, but checking the settings can help in crowded areas. Using a single network name for both bands lets devices move between them as the signal changes.
4. Add a mesh Wi-Fi system
A mesh system uses several units placed around the home that work together as one network. It is the best option for larger or multi-level homes. Place each unit within good range of the next, rather than in the dead spot itself.
5. Use a wired connection between access points
The most reliable setup connects mesh units or access points with Ethernet cable, often called wired backhaul. If running new cable is not practical, powerline adapters can carry network traffic over existing electrical wiring, although performance varies between homes.
6. Be careful with cheap range extenders
Basic range extenders repeat a weak signal, which often halves the speed and can make roaming between rooms unreliable. They can solve a single problem room, but a mesh system usually gives a better overall result.
Which fix suits your home?
| Your situation | Most likely fix |
|---|---|
| Small apartment with one weak room | Move the router, then consider a single access point |
| Single-level house with a router at one end | Relocate the router or add a two-unit mesh system |
| Large or multi-level house | Mesh system, ideally with wired backhaul |
| Double-brick or concrete home | Wired access points in key rooms |
| Slow even next to the router | Check the internet plan and replace an outdated router |
Common questions
Is mesh Wi-Fi better than an extender?
Usually, yes. Mesh units are designed to work together as one network and manage how devices move between them. Basic extenders repeat a signal and often reduce speed.
Should I separate my 2.4 GHz and 5 GHz networks?
For most homes, a single network name works best, because devices can choose the better band automatically. Some smart home devices only support 2.4 GHz, which a combined network still serves.
Does my NBN connection type affect Wi-Fi?
Your NBN connection type affects your internet speed, not your Wi-Fi coverage. However, the location of the NBN connection box often decides where the router sits, which strongly affects coverage. If your devices also run slowly, our guide to finding out why a computer is slow can help.